Description
1900/65A-00-01-01-00-00 BENTLY vibration monitoring system
1900/65A-00-01-01-00-00 BENTLY vibration monitoring system
Module Clips Drive controller servo moto
The 1900/65A-00-01-01-00-00 EGD Communication Gateway Integrates process control and other automation systems using both Ethernet TCP/IP and serial (RS232 / RS422 / RS485) communications capabilities. Permits Ethernet communications with 3500 Rack Configuration Software. The 1900/65A-00-01-01-00-00 also supports proprietary Bently Nevada protocol along with Modicon Modbus and Modbus/TCP protocols.
1900/65A-00-01-01-00-00Communication Gateway integrates easily with process control networks and other automation systems using both Ethernet TCP/IP and serial (RS232 / RS422 / RS485) communications capabilities. Permits communications via Modbus using 3500 Rack Configuration Software. The 1900/65A-00-01-01-00-00 can be configured using the 3500 Rack Configuration software to produce a custom or condensed Modbus map for communications using fixed or configurable registers. All vital rack information including direct vibration, gap, 1X, 2X, Smax, channel statuses, rack status, trip multiply, rack reset, and others can be easily communicated.
Contact: Mr. Lai
Wechat:17750010683
Whats app：+86 17750010683
Skype：+86 17750010683
QQ: 3221366881
3221366881@qq.com
Implementation of communication between ABC industrial robot and PLC based on DeviceNet fieldbus technology
introduction
In modern production systems, industrial robots and PLCs need to communicate and collaborate to complete production tasks. That is, the industrial robots output signals to the PLC, allowing the PLC to control related equipment to drive the robot’s front-end tools. This article mainly analyzes the communication problems between ABB industrial robots and PLC based on DeviceNet fieldbus technology. DeviceNet is a common network communication method in the field of automation. ABB industrial robots establish a network to communicate with Siemens PLC based on the DeviceNet network.
1Configure DSQC652
There are mainly 5 types of standard I/0 boards commonly used in ABB industrial robots [2]. Except for the different addresses assigned to them during setup, their configuration methods are basically the same. This article mainly analyzes the ABB standard I/0 board DS0C652, which mainly builds communication modules based on the DeviceNet network. The DS0C652 board has a distributed I/O module with 16 digital input and 16 digital output interfaces. The board is installed in the ABB industrial robot control cabinet. First, define the specific operation steps of the DS0C652 board, enter the teach pendant control panel, then enter the configuration menu (Figure 1), select the DeviceNetDevice menu, and add a template to enter Figure 2. ABB standard I/0 board is hung on the DeviceNet network, so the address of the module in the network must be set. The jumpers 6 to 12 of terminal x5 are used to determine the address of the module. The available address range is 10 to 63. Modify the parameters in the template parameters to complete the DS0C652 board settings. Click the drop-down menu to select the “Use value from template” row, select “DS0C65224VDCI/0Device”, and then the parameters that need to be set include the address of the I/0 board in the bus.
Figure 1 Configuring DSQC652
2Configure signals and parameters
After completing the DS0C652 board setting, the I/0 signal setting will be performed. Setting the I/0 signal is the basis for establishing communication with the PLC. The PLC communicates and transmits data with the ABB industrial robot through the I/0 signal and the DS0C652 board. As shown in Figure 3, in the signal configuration interface, there are many default I/0 points after the system is established. Modification is not allowed. Click “Add” to add signals. When setting input and output signals, their address range is 0~15. First, enter the signal menu in the configuration options to set the input and output types, and modify the corresponding parameters. After completing the settings, the computer prompts that you need to restart the settings. If there are multiple signals that need to be defined and the waiting time is long after restarting multiple times, you can click “Cancel” and wait for all signals to be defined before clicking the “Yes” button to restart. After the signal settings are completed, click to select “Input and Output” in the ABB menu to check whether all signals have been set.
Figure 2 Configure DSQC652 parameters
Figure 3 Signal parameter settings
During the signal establishment process, attention should be paid to the DSoC652 port and PLC port addresses used, and the corresponding address table should be established, as shown in Table 1. The robot interacts with the PLC through I/O signals. During the setting process, there must be no errors in the port and address number of the PLC connected to the DSoC652. If the address is set incorrectly, the communication between the robot and the PLC will not work properly.
The entire robot teaching pendant setting process is shown in Figure 4.
BENTLY 330100-90-01
BENTLY 330103-00-03-05-02-05
BENTLY 330103-00-04-10-02-00
BENTLY 330104-00-05-10-02-00
BENTLY 330104-00-05-10-02-CN
BENTLY 330105-02-12-05-02-05
BENTLY 330106-05-30-10-02-00
BENTLY 330108-91-05
BENTLY 330130-040-00-00
BENTLY 330130-040-01-00
BENTLY 330130-045-00-00
BENTLY 330130-080-00-00 Standard Extension Cable
BENTLY 330130-085-00-00
BENTLY 330180-90-05
BENTLY 330180-X1-CN
BENTLY 330703-000-070-10-02-05
BENTLY 330854-040-24-00
BENTLY 330901-05-32-05-02-00
BENTLY 330980-51-00
BENTLY 3500
BENTLY 3500/05-02-04-00-00-01
BENTLY 3500/05-01-02-00-00-01
BENTLY 3500/05-01-03-00-00-00
BENTLY 3500/15 133292-01
BENTLY 3500/20 125744-02
BENTLY 3500/22-01-01-00
BENTLY 3500/22M 288055-01
BENTLY 3500/22M 138607-01
BENTLY 3500/22M 288055-01
BENTLY 3500/25 125792-01
BENTLY 3500/25 149369-01
BENTLY 3500/32 125712-01
BENTLY 3500/32M 149986-02
BENTLY 3500/33
BENTLY 3500/33-01-00
BENTLY 3500/40M 176449-01
BENTLY 3500/40M（140734-01）
BENTLY 3500/42M 140734-02
BENTLY 3500/42M 176449-02
BENTLY 3500/45 176449-04
BENTLY 3500/45-01-00
BENTLY 3500/53 133388-01
BENTLY 3500/60 163179-01
BENTLY 3500/61 163179-02
BENTLY 3500/62
BENTLY 3500/70M 176449-08
BENTLY 3500/72M
BENTLY Communication gateway module 3500/91-01-01（161204-01+161216-01）
BENTLY 3500/92 136180-01
BENTLY 60M100-00
BENTLY 84152-01
BENTLY 9200-01-01-10-00
BENTLY ASSY78462-01U 78599-01A
1701/10-01 Temperature monitor BENTLY
3500/50 288062-02 BENTLY overspeed protection module
1.Has been engaged in industrial control industry for a long time, with a large number of inventories.
2.Industry leading, price advantage, quality assurance
3.Diversified models and products, and all kinds of rare and discontinued products
4.15 days free replacement for quality problems
ABB — AC 800M controller, Bailey, PM866 controller, IGCT silicon controlled 5SHY 3BHB01 3BHE00 3HNA00 DSQC series
BENTLY — 3500 system/proximitor, front and rear card, sensor, probe, cable 3500/20 3500/61 3500/05-01-02-00-001 3500/40M 176449-01 3500/22M 138607-01
Emerson — modbus card, power panel, controller, power supply, base, power module, switch 1C31,5X00, CE400, A6500-UM, SE3008,1B300,1X00,
EPRO — PR6423 PR6424 PR6425 PR6426 PR9376 PR9268 Data acquisition module, probe, speed sensor, vibration sensor
FOXBORO — FCP270 FCP280 FCM10EF FBM207 P0914TD CP40B FBI10E FBM02 FBM202 FBM207B P0400HE Thermal resistance input/output module, power module, communication module, cable, controller, switch
GE —- IS200/215/220/230/420 DS200/215 IC693/695/697/698 VMICPCI VMIVME 369-HI-R-M-0-0-E 469 module, air switch, I/O module, display, CPU module, power module, converter, CPU board, Ethernet module, integrated protection device, power module, gas turbine card
HIMA — F3 AIO 8/4 01 F3231 F8627X Z7116 F8621A 984862160 F3236 F6217 F7553 DI module, processor module, AI card, pulse encoder
Honeywell — Secure digital output card, program module, analog input card, CPU module, FIM card
MOOG — D136-001-007 Servo valve, controller, module
NI — SCXI-1100 PCI – PXIE – PCIE – SBRIO – CFP-AO-210 USB-6525 Information Acquisition Card, PXI Module, Card
Westinghouse — RTD thermal resistance input module, AI/AO/DI/DO module, power module, control module, base module
Woodward — 9907-164 5466-258 8200-1300 9907-149 9907-838 EASYGEN-3500-5/P2 8440-2145 Regulator, module, controller, governor
YOKOGAWA – Servo module, control cabinet node unit
Main products:
PLC, DCS, CPU module, communication module, input/output module (AI/AO/DI/DO), power module, silicon controlled module, terminal module, PXI module, servo drive, servo motor, industrial display screen, industrial keyboard, controller, encoder, regulator, sensor, I/O board, counting board, optical fiber interface board, acquisition card, gas turbine card, FIM card and other automatic spare parts
